CS Unitec Inc. Showroom

Visit CS Unitec Inc.  

 

   Found 44 results for "CS Unitec Inc."...

      Just show me: Everything | Articles | News | Products

Product

October 27, 2014
Portable magnetic drill features multiaxis positioning
CS Unitec’s new MAB 800 KTS portable magnetic drill features multiaxis positioning, allowing the drill to be adjusted up to 2.15625 in. forward and backward and up to 4.75 in. left and right after the magnet is adhered to the surface. The drill... Read more...

Product

July 28, 2014
Machine delivers double-sided deburring in one pass
CS Unitec’s Rolei BE 5 deburring machine performs double-sided deburring of stainless steel and aluminum sheets up to 0.2 in. thick in a single pass with no additional treatment. Two abrasive flap wheels rotate in opposite directions to grind... Read more...

Article

April 28, 2014
Beveling plate without the HAZ
Say you need a way to bevel that’s fast, extremely accurate, and, thanks to material property requirements, has little or no heat-affected zone (HAZ). Such application requirements have driven companies to alternative beveling technologies... Read more...

Product

April 22, 2014
Dry-cutting saw cuts metal up to 4.75-in. deep
The 8320 BigSaw from CS Unitec is the largest dry-cutting, portable metal saw on the market, according to the manufacturer. Featuring a 12.625-in.-dia., 80-tooth, carbide-tipped blade that can cut 4.75 in. deep without distortion, the saw cuts... Read more...

Product

March 20, 2014
Chop saw dry-cuts metal pipe, plate, profiles
CS Unitec’s new model 9435 Premium Super Dry Cutter cuts metal pipe, plate, and profiles without the need for lubrication or manual deburring. The 14-in. chop saw cuts up to 6 in. deep at 90 degrees in stainless steel, ferrous and nonferrous... Read more...

Article

February 10, 2014
The emergence of Saudi America
Few inventions have changed the dynamics of world trade more than the internal combustion engine. The four-stroke engine was perfected around 1876 in Duetz, Germany, shortly after the first commercially viable oil well was drilled in 1859 in... Read more...

Product

July 8, 2013
Dry-cutting miter saw makes 4-in.-deep cuts
CS Unitec has introduced a portable, dry-cutting miter saw for steel, stainless steel, and other materials. The model 9410 ND is the only metal cutting machine on the market with stepless adjustments from -45 to +45 degrees, according to the... Read more...

Product

May 21, 2013
Needle scalers deliver high power with low vibration
CS Unitec has introduced a line of low-vibration needle scalers with an optional dust shroud. The Trelawny™ Vibro-Lo™ VL series is designed to remove coatings and corrosion and clean other accumulated materials from metal surfaces.... Read more...

Product

March 21, 2013
Dry-cutting saw cuts 4.75 in. deep without coolant
The 8320 BigSaw2 from CS Unitec is the largest dry-cutting, portable metal saw on the market, according to the manufacturer. Featuring a 12.75.in.-dia., carbide-tipped blade that cuts up to 4.75 in. deep, the saw quickly processes steel,... Read more...

Product

January 24, 2013
Reversible drill motor drives weld prep, pipe fusion machines
CS Unitec's EAU 34/4 CB high-torque, reversible electric drill motor is suitable for a variety of turning operations that require high torque, multiple speeds, and forward and reverse direction. The heavy-duty drive motor is designed for... Read more...

Article

December 3, 2012
Grinding, polishing, blending in hard-to-reach areas
One of your customers calls to ask you to bid on a product currently in development. You’ve already been doing quite a few programs that involve bending tube and welding it to make subassemblies for his company, so he wants you to take... Read more...

Product

August 9, 2012
Beveling machine bevels steel pipe 6.25 in. and larger
CS Unitec's SKF 25 beveling machine provides quick, simplified preparation of weld seams and bevels steel pipes 6.25 in. dia. and larger. It is suitable for use on steel, stainless steel, aluminum, and nonferrous metals. The machine has a... Read more...

Product

May 31, 2012
Pneumatic circular saw features ultrathin blade for dry cutting
CS Unitec has introduced a 9-in. pneumatic circular saw for dry cutting steel plate up to 0.375 in. thick, as well as nonferrous metal and grating. The 19-lb. model 5 1115 0020 metal cutting saw is suitable for such industries as foundries,... Read more...

Article

May 1, 2012
Are cordless hand tools ready for metal fabricating?
For the do-it-yourself homeowner, the tool of choice is the cordless drill. It’s portable and gets the job done. Metal fabricators are similar to DIY guys. They usually don’t need assistance to complete a task, and they like... Read more...

Product

April 26, 2012
Cotton buffing wheel produces high mirror finish on metals
CS Unitec has introduced the CS 2410 cotton buffing wheel. Designed for use with polishing compounds, pastes, and rouges, the wheel produces a bright, high-mirror finish on stainless steel and other nonferrous metals. The wheel, made of cotton... Read more...

Article

January 10, 2012
Automating the deburring process
Manual deburring processes have been around for years, and the people who are good at them are regarded for their expertise, manual dexterity, and skill. But it is becoming increasingly difficult to find workers who want to learn the trade or... Read more...

Product

October 24, 2011
Elastic metal-cleaning disc suitable for thin sheet metal, cleaning welds on stainless steel, auto bodywork
MAGNUM CLEAN® is an elastic disc from CS Unitec Inc. for the deep cleaning of metals. The disc removes paint, rust, scale, and oil smears, cleaning and exposing without material removal. It is suitable for use in fabrication shops on thin... Read more...

Product

September 8, 2011
Pipe sander/grinder helps render seams invisible
CS Unitec's Pipe-Max weld seam grinder/pipe sander helps render weld seams invisible and can produce satin to mirror finishes on stainless steel, aluminum, and high-quality metal pipe and handrails. With a 14.5-amp, variable-speed (950 to... Read more...

Product

June 20, 2011
Magnetic drill with horizontal-motor mount suitable for drilling in tight spaces
Designed with a horizontal-motor mount, CS Unitec's new MAB 150 portable magnetic drill is suitable for drilling in tight spaces. The 7-in.-tall, 24-lb. drilling machine features a 9.25-amp, 110-V, double-insulated motor with a no-load speed... Read more...

Product

March 29, 2011
Cordless surface finisher usable for up to 15 minutes on one charge
The Poly PTX Accu 28V cordless longitudinal grinder from CS Unitec can be used for up to 15 min. on one charge. It is suitable for on-site use or assembly work when a power supply isn't available. Surface grinding and positioning are possible... Read more...

Product

January 24, 2011
Magnetic drilling machine suitable for drilling structural steel and other metals
CS Unitec's MAB 1300 magnetic drilling machine is designed for continuous use in heavy-duty drilling applications. Its 20-amp, 110-V, double-insulated, reversible motor is suitable for drilling structural steel and other metals. The... Read more...

Product

November 8, 2010
Pipe sander/grinder makes weld seams invisible, produces satin to mirror finishes on various materials
For surface finishing applications on pipe and handrails, CS Unitec's new Pipe-Max combination weld seam grinder and pipe sander makes weld seams invisible and can produce satin to mirror finishes on stainless steel, aluminum, and high-quality... Read more...

Product

August 17, 2010
Flexible-shaft grinder designed for awkward pieces, hard-to-reach areas
CS Unitec's Flexible Drive Shaft grinder is designed for grinding and polishing work on awkward pieces and in hard-to-reach areas. The flexible shaft converts any industrial angle grinder with a 5/8 by 11 spindle into a lightweight, hand-held... Read more...

Article

April 13, 2010
Industrial hand-held grinding and surface finishing — A primer on brush and mirror finishing
Finishing stainless steel, aluminum, and other nonferrous metals presents many challenges. Having the right equipment and following the appropriate steps not only produce the desired results, they save you time and effort. Welding, bending,... Read more...

Article

April 1, 2010
How to make grinding safer and more productive
Even people who sell hand power tools for a living aren't shy about an obvious truth: No child dreams of one day working in a fab shop's grinding department. The job can be dirty. It can be loud. And without the proper tools, protection, and... Read more...

Product

September 9, 2009
Flap discs reduce aluminum grinding temperature
CS Unitec's TIGER SHARK-PLANTEX® elastic discs are specially designed for the grinding aluminum. Flexible for grinding curved surfaces and shapes, the discs provide reduced grinding temperature, high material removal, and no glazing with... Read more...

Product

August 11, 2009
Deburring, beveling machine developed for large, awkward, heavy parts
CS Unitec's ROLEI(R) EF 115 hand-held deburring and beveling machine is designed for use on large, awkward, and heavy parts, such as machine tables, frame constructions, and large sheets of metal. According to the company, precise edge control... Read more...

Product

February 10, 2009
Diamond grinding disks suitable for hazardous environment use
CS Unitec's Eco Brazing (EB) diamond grinding disks reduce sparking to 1 percent of that produced by resinoid wheels, reports the company, making the disks suitable for use in hazardous environments such as nuclear plants and oil and gas... Read more...

Product

September 16, 2008
Pneumatic reciprocating saw certified for hazardous environment use
CS Unitec's 1.3-HP pneumatic reciprocating saw is ATEX certified (Class 112 GcT5) for use in hazardous environments. The saw's durability makes this tool suitable for use in refineries, offshore oil, marine, mining, petrochemical, power... Read more...

Product

July 15, 2008
Pneumatic magnetic drill approved for hazardous environment use
The Airbor AB-4300-2R portable magnetic drill from CS Unitec, designed to operate without the possibility of shock or blown circuitry, is ATEX-approved for use in hazardous environments (EX II 2 GcT6). Requiring no electricity, the drill's motor... Read more...

Product

March 11, 2008
Pipe sander polishes handrails, pipe, tubing
The LRP 1503 AIR Boa pipe sander from CS Unitec polishes handrails, pipe, and tubing. It has a 1-HP motor, with 20-CFM air consumption at 90 PSI and is lightweight. Operators can wrap the sanding arm up to 270 degrees around the radius of the... Read more...

Product

February 12, 2008
Surface finishing machine finishes steel, stainless steel, and nonferrous metals
CS Unitec's PTX Eco Smart surface finishing machine has balanced straight-line handling, high torque, and electronic speed control. It produces matte, satin, mirror, and other finishes on steel, stainless steel, and nonferrous metals.... Read more...

Product

November 6, 2007
Flap disks feature natural hemp with polypropylene binder backing plate
CS Unitec's new line of abrasive flap disks, which use the PLANTEX® high-tech compound, are the first in the world with a backing plate made of natural hemp with a polypropylene binder, the company reports. The abrasive fabric is 100 percent... Read more...

Product

July 24, 2007
Pipe sander suitable for stainless pipe and tubing
The LRP 1503 VRA Boa pipe sander from CS Unitec Inc. is suitable for hand rails, pipe, and tubing manufactured from stainless steel and other ferrous and nonferrous metals. Also suitable for cleaning pipe surfaces before welding, the... Read more...

Product

June 12, 2007
Pipe sander conceals weld seams, finishes stainless steel
CS Unitec's pipe sander conceals weld seams and provides a high-gloss finish on stainless steel. With an 11-amp, variable-speed electric or a 1-HP pneumatic motor with high torque, the sander finishes pipes from 3/8 to 10 in. dia. The ergonomic... Read more...

Product

May 8, 2007
Automatic feed clamp system simplifies pipe cutting
A portable pipe clamp system with automatic feed is available from CS Unitec for use with the company's portable pneumatic hacksaw. The system easily attaches to the hacksaw and pipe and operates off the same 90 PSI air supply as the saw. The... Read more...

Product

February 13, 2007
Finisher suitable for stainless steel, aluminum
CS Unitec's Industrial Sander/Polisher is suitable for cleaning welds on stainless steel, aluminum and other metals. With a 4-in.-wide face, it produces shadow-free surfaces, up to a #4 brush finish, quickly and easily. The unit weighs only eight... Read more...

Product

February 13, 2007
Multipurpose beveling machine offered
CS Unitec's beveling machine bevels, deburrs, and chamfers steel, stainless steel, nonferrous metals, and brass. The compact, lightweight machine is designed to be used with two interchangeable milling cutter heads that offer a choice of two... Read more...

Article

July 10, 2003
Fabricating technology advancements drive new plate finishing trends
As cutting, welding, and other fabrication processes evolve and new materials emerge to meet these requirements, finishing processes have had to become a nimble dance partner to the whirlwind of change or get caught up in it. Producing... Read more...

Article

October 12, 2002
Sanding Machine Finishes the Job
AMS Corporation, a miscellaneous-metals fabricator in Taunton, Mass., recently took on a large project for Olin College of Engineering, a new institution of higher learning near Boston. The project called for fabricating about 1,500 feet... Read more...